CAS #:

Linear Formula:

Al(H2PO4)3

MDL Number:

MFCD00014152

EC No.:

236-875-2

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
≥95% Aluminum Phosphate Monobasic
AL-H2PAT-0151
Pricing > SDS > Data Sheet >
(2N) 99% Aluminum Phosphate Monobasic
AL-H2PAT-02
Pricing > SDS > Data Sheet >
(3N) 99.9% Aluminum Phosphate Monobasic
AL-H2PAT-03
Pricing > SDS > Data Sheet >
(4N) 99.99% Aluminum Phosphate Monobasic
AL-H2PAT-04
Pricing > SDS > Data Sheet >
(5N) 99.999% Aluminum Phosphate Monobasic
AL-H2PAT-05
Pricing > SDS > Data Sheet >

Aluminum Phosphate Monobasic Properties (Theoretical)

Compound Formula AlH6O12P3
Molecular Weight 317.94
Appearance White powder
Melting Point N/A
Boiling Point N/A
Density N/A
Solubility in H2O Soluble
Exact Mass 317.888749
Monoisotopic Mass 317.888749

Aluminum Phosphate Monobasic Health & Safety Information

Signal Word Danger
Hazard Statements H318
Hazard Codes C
Precautionary Statements P280-P305+P351+P338-P310
Risk Codes N/A
Safety Statements N/A
Transport Information NONH for all modes of transport
WGK Germany 3
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 03/18/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Aluminum Phosphate Monobasic

Product Number: All applicable American Elements product codes, e.g. AL-H2PAT-02 , AL-H2PAT-03 , AL-H2PAT-04 , AL-H2PAT-05 , AL-H2PAT-0151

CAS #: 13530-50-2

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture
GHS Classification in accordance with 29 CFR 1910 (OSHA HCS)
Serious eye damage (Category 1), H318
For the full text of the H-Statements mentioned in this Section, see Section 16.
GHS Label elements, including precautionary statements
Pictogram

Corrosion - GHS05

Signal word: Danger
Hazard statement(s)
H318
Causes serious eye damage.
Precautionary statement(s)
P280
Wear eye protection/ face protection.
P305 + P351 + P338 + P310
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor.
Hazards not otherwise classified (HNOC) or not covered by GHS - none


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substances
Formula: H6AlO12P3
Molecular weight: 317.94 g/mol
CAS-No.: 13530-50-2
EC-No.: 236-875-2


SECTION 4. FIRST AID MEASURES

Description of first aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Consult a physician.
In case of eye contact
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
If swallowed
Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11
Indication of any immediate medical attention and special treatment needed
No data available


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Special hazards arising from the substance or mixture
No data available
Advice for firefighters
Wear self-contained breathing apparatus for firefighting if necessary.
Further information
No data available


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust.
For personal protection see section 8.
Environmental precautions
Do not let product enter drains.
Methods and materials for containment and cleaning up
Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
Reference to other sections
For disposal see section 13.


SECTION 7. HANDLING AND STORAGE

Precautions for safe handling
Avoid formation of dust and aerosols.
Further processing of solid materials may result in the formation of combustible dusts. The potential for combustible dust formation should be taken into consideration before additional processing occurs.
Provide appropriate exhaust ventilation at places where dust is formed.
For precautions see section 2.2.
Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Keep in a dry place.
Keep in a dry place.
Storage class (TRGS 510): Non Combustible Solids
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure controls
Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Personal protective equipment
Eye/face protection
Face shield and safety glasses Use equipment for eye protection tested and approved under appropriate government standards such as N
IOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
Body Protection
Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face particle respirator type N100 (US) or type P3 (EN 143) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Control of environmental exposure
Do not let product enter drains.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance
Form: powder
Colour: white
Odour
No data available
Odour Threshold
No data available
pH
No data available
Melting point/freezing point
Melting point/freezing point
: > 449.85 °C (> 841.73 °F)
Initial boiling point and boiling range
No data available
Flash point
Not applicable
Evaporation rate
No data available
Flammability (solid, gas)
No data available
Upper/lower flammability or explosive limits
No data available
Vapour pressure
No data available
Vapour density
2.34 at 21 °C (70 °F)
Relative density
No data available
Water solubility
294 g/l at 20 °C (68 °F)-soluble
Partition coefficient: n-octanol/water
No data available
Auto-ignition temperature
No data available
Decomposition temperature
No data available
Viscosity
No data available
Explosive properties
No data available
Oxidizing properties
No data available
Other safety information
Relative vapour density
2.34 at 21 °C (70 °F)


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
No data available
Conditions to avoid
No data available
Incompatible materials
Strong oxidizing agents
Hazardous decomposition products
Hazardous decomposition products formed under fire conditions. - Oxides of phosphorus, Aluminum oxide
Other decomposition products - No data available
In the event of fire: see section 5


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity
LD50
Oral-Rat-female-> 2,000 mg/kg(Fixed Dose Method)LC50
Inhalation-Rat-male and female-4 h-> 5.1 mg/l
(OECD Test Guideline 403)
Dermal:
No data available
No data available
Skin corrosion/irritation
No data available
Serious eye damage/eye irritation
No data available
Respiratory or skin sensitisation
No data available
Germ cell mutagenicity
No data available
Carcinogenicity
IARC:
No component of this product present at levels greater than or equal to 0.1% is identified as
probable, possible or confirmed human carcinogen by IARC.
NTP:
No component of this product present at levels greater than or equal to 0.1% is identified as a
known or anticipated carcinogen by NTP.
OSHA:
No component of this product present at levels greater than or equal to 0.1% is identified as a
carcinogen or potential carcinogen by OSHA.
Reproductive toxicity
No data available
No data available
Specific target organ toxicity -single exposure
No data available
Specific target organ toxicity -repeated exposure
No data available
Aspiration hazard
No data available
Additional Information
RTECS: Not available


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
No data available
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
Other adverse effects
No data available


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Product
Offer surplus and non-recyclable solutions to a licensed disposal company.
Contaminated packaging
Dispose of as unused product.


SECTION 14. TRANSPORT INFORMATION

DOT (US)
Not dangerous goods
IMDG
Not dangerous goods
IATA
Not dangerous goods


SECTION 15. REGULATORY INFORMATION

SARA 302
Components
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313
Components
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
Massachusetts Right To Know
Components
No components are subject to the Massachusetts Right to Know Act.
Pennsylvania Right To Know
Components
Aluminium tris(dihydrogen phosphate)
CAS-No.13530-50-2
Revision Date
1989-08-11
New Jersey Right To Know
Components
Aluminium tris(dihydrogen phosphate)
CAS-No.13530-50-2
Revision Date
1989-08-11
California Prop. 65
Components
This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Aluminum Phosphate Monobasic

High purity Aluminum Phosphate MonobasicAluminum Phosphate Monobasic (also known as aluminum dihydrogen phosphate) is generally immediately available in most volumes. American Elements produces to many standard grades when applicable, including Mil Spec (military grade); ACS, Reagent and Technical Grade; Food, Agricultural and Pharmaceutical Grade; Optical Grade, USP and EP/BP (European Pharmacopoeia/British Pharmacopoeia) and follows applicable ASTM testing standards. Typical and custom packaging is available. Additional technical, research and safety (MSDS) information is available as is a Reference Calculator for converting relevant units of measurement.

Aluminum Phosphate Monobasic Synonyms

Aluminum dihydrogen orthophosphate, Aluminum dihydrogen phosphate, Aluminum hydrogen triphosphate, Aluminum tris(dihydrogen phosphate), Aluminum dihydrogenphosphate, Aluminum hydrogenphosphate, prim-Aluminum phosphate, Phosphoric acid, aluminum salt, CAS 13939-25-8, EC 237-714-9

Chemical Identifiers

Linear Formula Al(H2PO4)3
MDL Number MFCD00014152
EC No. 236-875-2
Beilstein/Reaxys No. N/A
Pubchem CID 9818426
IUPAC Name aluminum; dihydrogen phosphate
SMILES OP(=O)(O)[O-].OP(=O)(O)[O-].OP(=O)(O)[O-].[Al+3]
InchI Identifier InChI=1S/Al.3H3O4P/c;3*1-5(2,3)4/h;3*(H3,1,2,3,4)/q+3;;;/p-3
InchI Key RGPUVZXXZFNFBF-UHFFFAOYSA-K

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

Aluminum

See more Aluminum products. Aluminum (or Aluminium) (atomic symbol: Al, atomic number: 13) is a Block P, Group 13, Period 3 element with an atomic weight of 26.9815386. It is the third most abundant element in the earth's crust and the most abundant metallic element. Aluminum Bohr Model Aluminum's name is derived from alumina, the mineral from which Sir Humphrey Davy attempted to refine it from in 1812. Aluminum was first predicted by Antoine Lavoisier 1787 and first isolated by Hans Christian Øersted in 1825. Aluminum is a silvery gray metal that possesses many desirable characteristics. It is light, nonmagnetic and non-sparking. It stands second among metals in the scale of malleability, and sixth in ductility. It is extensively used in many industrial applications where a strong, light, easily constructed material is needed. Elemental AluminumAlthough it has only 60% of the electrical conductivity of copper, it is used in electrical transmission lines because of its light weight. Pure aluminum is soft and lacks strength, but alloyed with small amounts of copper, magnesium, silicon, manganese, or other elements, it imparts a variety of useful properties.

Phosphorus

Phosphorus Bohr ModelSee more Phosphorus products. Phosphorus (atomic symbol: P, atomic number: 15) is a Block P, Group 15, Period 3 element. The number of electrons in each of Phosphorus's shells is 2, 8, 5 and its electronic configuration is [Ne] 3s2 3p3. The phosphorus atom has a radius of 110.5.pm and its Van der Waals radius is 180.pm. Phosphorus is a highly-reactive non-metallic element (sometimes considered a metalloid) with two primary allotropes, white phosphorus and red phosphorus its black flaky appearance is similar to graphitic carbon. Compound forms of phosphorus include phosphates and phosphides. Phosphorous was first recognized as an element by Hennig Brand in 1669 its name (phosphorus mirabilis, or "bearer of light") was inspired from the brilliant glow emitted by its distillation.

TODAY'S TOP DISCOVERY!

March 18, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
Enhancing CO Oxidation: The Impact of a Nanoscale Metal Oxide Layer on Gold and Platinum Nanoparticle Catalysts

Enhancing CO Oxidation: The Impact of a Nanoscale Metal Oxide Layer on Gold and Platinum Nanoparticle Catalysts