Iridium Foil
| Product | Product Code |
Order or Specifications |
99% Iridium Foil |
IR-M-02F
|
 |
99.5% Iridium Foil |
IR-M-025F
|
|
99.9% Iridium Foil |
IR-M-03F
|
|
99.95% Iridium Foil |
IR-M-035F
|
|
99.99% Iridium Foil |
IR-M-04F |
|
99.999% Iridium Foil |
IR-M-05F
|
|
See research below. American Elements specializes in producing Iridium as rolled foils and sheets in various thicknesses and sizes. Most foils are produced from cast ingots for use in coating and thin film Chemical Vapor Deposition (CVD) and Physical Vapor Deposition (PVD) processes including 
Thermal and Electron Beam (E-Beam) Evaporation, Low Temperature Organic Evaporation, Atomic Layer Deposition (ALD), Organometallic and Chemical Vapor Deposition (MOCVD) for specific applications such as fuel cells and solar energy. Thickness can range from 0.003" to approximately 2mm for all metals. Some metals can also be rolled down as thin as 0.001". Piece sizes are available up to approximately 7" maximum width. Maximum lengths of about 20" can be obtained with a nominal thickness between about 0.005" and 0.020" for thin film deposition on glass or metal substrates. Materials are produced using crystallization, solid state and other ultra high purification processes such as sublimation. American Elements specializes in producing custom compositions for commercial and research applications and for new proprietary technologies. American Elements also casts any of the rare earth metals and most other advanced materials into rod, bar or plate form, as well as other machined shapes and through other processes such as nanoparticles (See also application discussion at Nanotechnology Information and at Quantum Dots) and in the form of solutions and organometallics. We also produce Iridium as rods, powder and plates. Other shapes are available by request.
Thermal and Electron Beam (E-Beam) Evaporation, Low Temperature Organic Evaporation, Atomic Layer Deposition (ALD), Organometallic and Chemical Vapor Deposition (MOCVD) for specific applications such as fuel cells and solar energy. Thickness can range from 0.003" to approximately 2mm for all metals. Some metals can also be rolled down as thin as 0.001". Piece sizes are available up to approximately 7" maximum width. Maximum lengths of about 20" can be obtained with a nominal thickness between about 0.005" and 0.020" for thin film deposition on glass or metal substrates. Materials are produced using crystallization, solid state and other ultra high purification processes such as sublimation. American Elements specializes in producing custom compositions for commercial and research applications and for new proprietary technologies. American Elements also casts any of the rare earth metals and most other advanced materials into rod, bar or plate form, as well as other machined shapes and through other processes such as nanoparticles (See also application discussion at Nanotechnology Information and at Quantum Dots) and in the form of solutions and organometallics. We also produce Iridium as rods, powder and plates. Other shapes are available by request.Iridium is a Block D, Group 9, Period 6 element. The electronic configuration is [Xe] 4f14 5d7 6s2. In its elemental form iridium's CAS number is 7439-88-5. The iridium atom has a radius of 135.7.pm and it's Van der Waals radius is 200.pm. Iridium is a member of the platinum group of metals. It is the most corrosion resistant metal known. It will not react with any acid and can only be attacked by certain molten salts, such as molten sodium chloride. It is alloyed with platinum to produce highly corrosive resistant electrical contacts for spark plugs.
| Formula | CAS No. | Appearance | Molecular Weight |
| Ir | 7439-88-5 | Gray | 192.22 |
| PRODUCT CATALOG | Submicron & Nanopowder | Tolling | Ultra High Purity | Sputtering Target | Crystal Growth | Rod, Plate, Powder, etc. |
© 2001-2008. American Elements is a U.S. Registered Trademark. All rights reserved.
This website and all pages, designs, concepts, logos, and color schemes herein are
the copyrighted proprietary rights and intellectual property of American Elements.
This website and all pages, designs, concepts, logos, and color schemes herein are
the copyrighted proprietary rights and intellectual property of American Elements.
|
Recent Research & Development for Iridium
|
| American Elements Products can also be sourced at these sites: | |||||||
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
electronics-ee.com |  |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
|
 |
 |
 |
 |
 |
 |
 |
|