Silver Tetrafluoroborate

CAS #:

Linear Formula:

AgBF4

MDL Number:

MFCD00003408

EC No.:

237-956-5

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Silver Tetrafluoroborate
AG-FBAT-02
Pricing > SDS > Data Sheet >
(2N5) 99.5% Silver Tetrafluoroborate
AG-FBAT-025
Pricing > SDS > Data Sheet >
(3N) 99.9% Silver Tetrafluoroborate
AG-FBAT-03
Pricing > SDS > Data Sheet >
(3N5) 99.95% Silver Tetrafluoroborate
AG-FBAT-035
Pricing > SDS > Data Sheet >
(4N) 99.99% Silver Tetrafluoroborate
AG-FBAT-04
Pricing > SDS > Data Sheet >
(5N) 99.999% Silver Tetrafluoroborate
AG-FBAT-05
Pricing > SDS > Data Sheet >

Silver Tetrafluoroborate Properties (Theoretical)

Compound Formula AgBF4
Molecular Weight 194.67
Appearance White to off-white crystalline solid or powder
Melting Point 200 °C
Boiling Point N/A
Density 0.936 g/mL @ 20 °C
Solubility in H2O N/A
Exact Mass 193.908015
Monoisotopic Mass 193.908015

Silver Tetrafluoroborate Health & Safety Information

Signal Word Danger
Hazard Statements H314
Hazard Codes C
Precautionary Statements P280-P305 + P351 + P338-P310
Flash Point Not applicable
Risk Codes 34
Safety Statements 26-36/37/39-45
RTECS Number ED2875000
Transport Information UN 3260 8 / PGII
WGK Germany 3
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 03/28/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Silver Tetrafluoroborate

Product Number: All applicable American Elements product codes, e.g. AG-FBAT-02 , AG-FBAT-025 , AG-FBAT-03 , AG-FBAT-035 , AG-FBAT-04 , AG-FBAT-05

CAS #: 14104-20-2

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

OSHA Haz Com: CFR 1910.1200: Acute Toxicity - Oral [Category 4]
Eye Damage/Irritation [Category 1]
Skin Corrosion/Irritation [Category 1B]
Signal word: Danger!
Hazard Statement(s): Causes serious eye damage
Causes severe skin burns and eye damage
Harmful if swallowed

Corrosion - GHS05 Exclamation Mark - GHS07

Pictogram(s) or Symbol(s):
Precautionary Statement(s):
[Prevention] Do not eat, drink or smoke when using this product. Wash hands and face thoroughly after handling. Do
not breathe dusts or mists. Use only outdoors or in a well-ventilated area. Wear protective gloves,
protective clothing, eye protection and face protection. Wear eye protection. Wear face protection (full
length face shield).
[Response] If swallowed: Immediately call a poison center or doctor. Rinse mouth. If swallowed: Rinse mouth. Do NOT
induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water
or shower. Wash contaminated clothing before reuse. If inhaled: Remove person to fresh air and keep
comfortable for breathing. Immediately call a poison center or doctor. If in eyes: Rinse cautiously with
water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
[Storage] Store locked up.
[Disposal] Dispose of contents and container in accordance with US EPA guidelines for the classification and
determination of hazardous waste listed in 40 CFR 261.3. (See Section 13)


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substance/Mixture: Substance
Components: Silver Tetrafluoroborate
Percent: >98.0%(T)
CAS Number: 14104-20-2
Molecular Weight: 194.67
Chemical Formula: AgBF4


SECTION 4. FIRST AID MEASURES

Inhalation: Immediately call a poison center or doctor. Effects of exposure (inhalation) to substance may be delayed.
Move victim to fresh air. Give artificial respiration if victim is not breathing. Administer oxygen if breathing is
difficult. Keep victim warm and quiet. Treat symptomatically and supportively. Ensure that medical
personnel are aware of the material(s) involved and take precautions to protect themselves.
Skin contact: For severe burns, immediate medical attention is required. Immediately call a poison center or doctor.
Remove and wash contaminated clothing before re-use. Remove and isolate contaminated clothing and
shoes. In case of contact with substance, immediately flush skin with running water for at least 20 minutes.
Treat symptomatically and supportively. Ensure that medical personnel are aware of the material(s)
involved and take precautions to protect themselves.
Eye contact: IMMEDIATELY flush eyes with running water for at least 15 minutes, keeping eyelids open. Eye contact
with vapors or substance may cause severe injury, burns, or death. Call emergency medical service. Move
victim to fresh air. Check for and remove any contact lenses. Keep victim warm and quiet. Treat
symptomatically and supportively. Effects of exposure to substance may be delayed. Ensure that medical
personnel are aware of the material(s) involved and take precautions to protect themselves.
Ingestion: Harmful if swallowed. Do not induce vomiting with out medical advice. Call a physician or Poison Control
Center immediately. Do not use mouth-to-mouth method if victim ingested the substance; give artificial
respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory
medical device. Loosen tight clothing such as a collar, tie, belt or waistband. If a person vomits place them
in the recovery position so that vomit will not reenter the mouth and throat. Rinse mouth. Keep victim warm
and quiet. Treat symptomatically and supportively. Ensure that medical personnel are aware of the
material(s) involved and take precautions to protect themselves.
Symptoms/effects:
Acute: Pain. Redness.
Delayed: No data available
Immediate medical attention: WARNING: It might be hazardous to the person providing aid to give mouth-to-mouth respiration, because
the inhaled material is harmful. WARNING: It might be hazardous to the person providing aid to give
mouth-to-mouth respiration, because the inhaled material is corrosive. For severe burns, immediate
medical attention is required. If breathing has stopped, perform artificial respiration. Use first aid treatment
according to the nature of the injury. Ensure that medical personnel are aware of the material(s) involved
and take precautions to protect themselves.


SECTION 5. FIREFIGHTING MEASURES

Suitable extinguishing media: Dry chemical, CO2 or water spray. Consult with local fire authorities before attempting large scale fire
fighting operations.
Specific hazards arising from the chemical
Hazardous combustion products: These products include: Halogenated compounds Borates Metallic oxides
Other specific hazards: WARNING: Highly toxic HF gas is produced during combustion.
Special precautions for fire-fighters:
Use water spray or fog; do not use straight streams. Dike fire-control water for later disposal; do not scatter the material. Containers may explode when
heated. Move containers from fire area if you can do it without risk.
Special protective equipment for fire-fighters:
Wear positive pressure self-contained breathing apparatus (SCBA). Structural fire fighters' protective clothing provides limited protection in fire situations
ONLY; it may not be effective in spill situations. Wear chemical protective clothing which is specifically recommended by the manufacturer. It may
provide little or no thermal protection.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions: Avoid contact with skin, eyes, and clothing. Keep people away from and upwind of spill/leak. Do not touch
damaged containers or spilled material unless wearing appropriate protective clothing (Section 8). Warn
unnecessary personnel to move away. Stop leak if you can do it without risk. Ensure adequate ventilation.
Isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Personal protective equipment: Wear eye protection (splash goggles) and face protection (full length face shield). Lab coat. Dust
respirator. Be sure to use a MSHA/NIOSH approved respirator or equivalent. Wear protective gloves
(nitrile).
Emergency procedures: Prevent dust cloud. In case of a spill and/or a leak, always shut off any sources of ignition, ventilate the
area, and excercise caution. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Warn personnel to move away. Prevent entry into sewers, basements or
confined areas; dike if needed.
Methods and materials for containment and cleaning up:
ELIMINATE all ignition sources (no smoking, flares, sparks, or flames in immediate area). Stop leak if without risk. Ventilate the area. Absorb with an
inert material and put the spilled material in an appropriate waste disposal container. Use clean non-sparking tools to collect absorbed material.
Environmental precautions:
Keep away from living quarters. Prevent further leakage or spillage if safe to do so. Water runoff can cause environmental damage. Prevent entry into
sewers, basements or confined areas; dike if needed.


SECTION 7. HANDLING AND STORAGE

Precautions for safe handling: Avoid inhalation of vapor or mist. Manipulate under an adequate fume hood. Do not ingest. Avoid contact
with skin and eyes. Use process enclosures, local exhaust ventilation, or other engineering controls to
keep airborne levels below recommended exposure limits. Keep container dry. Handle and open container
with care. Wear suitable protective clothing, gloves and eye/face protection. When using do not eat, drink,
or smoke. Keep away from sources of ignition.
Conditions for safe storage: Store locked up. Keep containers tightly closed in a cool, well-ventilated place. Keep away from
incompatibles. Containers which are opened must be carefully resealed and kept upright to prevent
leakage. Avoid prolonged storage periods. Store under inert gas (e.g. Argon). Hygroscopic material, store
in a tightly sealed container.
Storage incompatibilities: Bases, Store away from oxidizing agents


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure limits:
ACGIH TLV (TWA): 0.01 mg (Ag)/m3
OSHA PEL (TWA): 2.5 mg (F)/m3
Appropriate engineering controls:
Use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below recommended exposure limits. Ventilation
is normally required when handling or using this product. Eyewash fountains should be provided in areas where there is any possibility that workers
could be exposed to the substance. Follow safe industrial engineering/laboratory practices when handling any chemical.
Personal protective equipment
Respiratory protection: Dust respirator. Be sure to use a MSHA/NIOSH approved respirator or equivalent.
Hand protection: Nitrile gloves.
Eye protection: Safety glasses.
Skin and body protection: Wear protective clothing (lab coat and chemical resistant boots).


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Physical state (20°C): Solid
Form: Crystal - Powder
Color: White - Almost white
Odor: No data available
Odor threshold: No data available

Melting point/freezing point: 73°C (163°F)
Boiling point/range: No data available
Decomposition temperature: No data available
Relative density: No data available
Kinematic Viscosity: No data available
Partition coefficient: No data available
n-octanol/water (log Pow)
Flash point: No data available
Flammability (solid, gas): No data available

pH: No data available
Vapor pressure: No data available
Vapor density: No data available
Dynamic Viscosity: No data available
Evaporation rate: No data available
(Butyl Acetate = 1)
Autoignition temperature: No data available
Flammability or explosive limits: No data available
Lower: No data available
Upper: No data available

Solubility(ies):
Water: Very soluble
Very soluble: Ether, Toluene
Soluble: Benzene


SECTION 10. STABILITY AND REACTIVITY

Reactivity: Not Available.
Chemical Stability: Moisture sensitive. Light sensitive.
Possibility of Hazardous Reactions: No hazardous reactivity has been reported.
Conditions to avoid: Exposure to light. Exposure to moisture. Moisture sensitive.
Incompatible materials: Oxidizing agents, Strong acids
Hazardous Decomposition Products: No data available


SECTION 11. TOXICOLOGICAL INFORMATION

RTECS Number: ED2875000
Acute Toxicity:
ivn-mus LD50:56 mg/kg
Skin corrosion/irritation:
No data available
Serious eye damage/irritation:
No data available
Respiratory or skin sensitization:
No data available
Germ cell mutagenicity:
No data available
Carcinogenicity:
No data available
IARC: No data available NTP: No data available OSHA: No data available
Reproductive toxicity:
No data available
Routes of Exposure: Inhalation, Eye contact, Ingestion, Skin contact.
Symptoms related to exposure:
Overexposure may result in serious illness or death. Skin contact may produce burrns. Skin contact may result in inflammation; characterized by itching,
scaling, reddening, or occasionally blistering. Eye contact can result in corneal damage or blindness.
Potential Health Effects:
No specific information available; skin and eye contact may result in irriatation. May be harmful if inhaled or ingested.
Target organ(s): No data available


SECTION 12. ECOLOGICAL INFORMATION

Ecotoxicity
Fish: No data available
Crustacea: No data available
Algae: No data available
Persistence and degradability: No data available
Bioaccumulative potential (BCF): No data available
Mobillity in soil: No data available
Partition coefficient:
n-octanol/water (log Pow)
No data available
Soil adsorption (Koc): No data available
Henry's Law:
constant (PaM3/mol)
No data available


SECTION 13. DISPOSAL CONSIDERATIONS

Disposal of product: Recycle to process if possible. It is the generator's responsibility to comply with Federal, State and Local
rules and regulations. You may be able to dissolve or mix material with a combustible solvent and burn in a
chemical incinerator equipped with an afterburner and scrubber system. This section is intended to provide
assistance but does not replace these laws, nor does compliance in accordance with this section ensure
regulatory compliance according to the law. US EPA guidelines for Identification and Listing of Hazardous
Waste are listed in 40 CFR Parts 261. The product should not be allowed to enter the environment, drains,
water ways, or the soil.
Disposal of container: Dispose of as unused product. Do not re-use empty containers.
Other considerations: Observe all federal, state and local regulations when disposing of the substance.


SECTION 14. TRANSPORT INFORMATION

DOT (US)
UN number:
UN3260
Proper Shipping Name:
Corrosive solid, acidic, inorganic, n.o.s.
Class or Division:
8 Corrosive material
Packing Group:
II
IATA
UN number:
UN3260
Proper Shipping Name:
Corrosive solid, acidic, inorganic, n.o.s.
Class or Division:
8 Corrosive material
Packing Group:
II
IMDG
UN number:
UN3260
Proper Shipping Name:
Corrosive solid, acidic, inorganic, n.o.s.
Class or Division:
8 Corrosive material
Packing Group:
II
EmS number: F-A, S-B


SECTION 15. REGULATORY INFORMATION

Toxic Substance Control Act (TSCA 8b.):
This product is ON the EPA Toxic Substances Control Act (TSCA) inventory.
US Federal Regulations
CERCLA Hazardous substance and Reportable Quantity:
SARA 313: Not Listed
SARA 302: Not Listed
State Regulations
State Right-to-Know
Massachusetts Not Listed
New Jersey Not Listed
Pennsylvania Not Listed
California Proposition 65: Not Listed
Other Information
NFPA Rating:
Health: 3
Flammability: 0
Instability: 0
HMIS Classification:
Health: 3
Flammability: 0
Physical: 0
International Inventories
WHMIS hazard class: E: Corrosive material.
D2A: Materials causing other toxic effects. (Very Toxic)
EC-No: 237-956-5


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Silver Tetrafluoroborate

Silver Tetrafluoroborate is generally immediately available in most volumes. High purity, submicron and nanopowder forms may be considered. American Elements produces to many standard grades when applicable, including Mil Spec (military grade); ACS, Reagent and Technical Grade; Food, Agricultural and Pharmaceutical Grade; Optical Grade, USP and EP/BP (European Pharmacopoeia/British Pharmacopoeia) and follows applicable ASTM testing standards. Typical and custom packaging is available. Additional technical, research and safety (MSDS) information is available as is a Reference Calculator for converting relevant units of measurement.

Silver Tetrafluoroborate Synonyms

Tetrafluoroboric acid silver salt, Silver borofluoride, Silver(1+) tetrafluoroborate, Borate(1-), tetrafluoro-, silver(1+) (1:1), Silver(I) tetrafluoroborate, Silver fluoroborate

Chemical Identifiers

Linear Formula AgBF4
MDL Number MFCD00003408
EC No. 237-956-5
Beilstein/Reaxys No. N/A
Pubchem CID 159722
IUPAC Name silver; tetrafluoroborate
SMILES [Ag+].F[B-](F)(F)F
InchI Identifier InChI=1S/Ag.BF4/c;2-1(3,4)5/q+1;-1
InchI Key CCAVYRRHZLAMDJ-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

Boron

See more Boron products. Boron Bohr ModelBoron (atomic symbol: B, atomic number: 5) is a Block P, Group 13, Period 2 element with an atomic weight of 10.81. The number of electrons in each of boron's shells is 2, 3 and its electron configuration is [He] 2s2 2p1. The boron atom has a radius of 90 pm and a Van der Waals radius of 192 pm. Boron was discovered by Joseph Louis Gay-Lussac and Louis Jacques Thénard in 1808 and was first isolated by Humphry Davy later that year. Boron is classified as a metalloid is not found naturally on earth. Elemental BoronAlong with carbon and nitrogen, boron is one of the few elements in the periodic table known to form stable compounds featuring triple bonds. Boron has an energy band gap of 1.50 to 1.56 eV, which is higher than that of either silicon or germanium. The name Boron originates from a combination of carbon and the Arabic word buraqu meaning borax.

Fluorine

Fluorine is a Block P, Group 17, Period 2 element. Its electron configuration is [He]2s22p5. The fluorine atom has a covalent radius of 64 pm and its Van der Waals radius is 135 pm. In its elemental form, CAS 7782-41-4, fluorine gas has a pale yellow appearance. Fluorine was discovered by André-Marie Ampère in 1810. It was first isolated by Henri Moissan in 1886.

Silver

See more Silver products. Silver (atomic symbol: Ag, atomic number: 47) is a Block D, Group 11, Period 5 element with an atomic weight of 107.8682. Silver Bohr ModelThe number of electrons in each of Silver's shells is 2, 8, 18, 18, 1 and its electron configuration is [Kr]4d10 5s1. The silver atom has a radius of 144 pm and a Van der Waals radius of 203 pm. Silver was first discovered by Early Man prior to 5000 BC. In its elemental form, silver has a brilliant white metallic luster. Elemental SilverIt is a little harder than gold and is very ductile and malleable, being exceeded only by gold and perhaps palladium. Pure silver has the highest electrical and thermal conductivity of all metals and possesses the lowest contact resistance. It is stable in pure air and water, but tarnishes when exposed to ozone, hydrogen sulfide, or air containing sulfur. It is found in copper, copper-nickel, lead, and lead-zinc ores, among others. Silver was named after the Anglo-Saxon word "seolfor" or "siolfur," meaning 'silver'.

TODAY'S TOP DISCOVERY!

March 28, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
University of Michigan researchers develop new fabrication process for helical metal nanoparticles

University of Michigan researchers develop new fabrication process for helical metal nanoparticles