Aluminum Sulfate (Anhydrous)

CAS #:

Linear Formula:

Al2(SO4)3

MDL Number:

MFCD00003423

EC No.:

233-135-0

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Aluminum Sulfate
AL-SAT-02-C.AHYD
Pricing > SDS > Data Sheet >
(3N) 99.9% Aluminum Sulfate
AL-SAT-03-C.AHYD
Pricing > SDS > Data Sheet >
(4N) 99.99% Aluminum Sulfate
AL-SAT-04-C.AHYD
Pricing > SDS > Data Sheet >
(5N) 99.999% Aluminum Sulfate
AL-SAT-05-C.AHYD
Pricing > SDS > Data Sheet >

Aluminum Sulfate (Anhydrous) Properties (Theoretical)

Compound Formula Al2O12S3
Molecular Weight 360.166157
Appearance White Crystals or Powder
Melting Point 770° C
Boiling Point N/A
Density 2.71 g/cm3 (20 °C)
Solubility in H2O Soluble
pH 3.5 (20 °C)
Exact Mass 359.82883
Monoisotopic Mass 359.82883

Aluminum Sulfate (Anhydrous) Health & Safety Information

Signal Word Danger
Hazard Statements H290-H318
Hazard Codes C
Precautionary Statements P280-P305 + P351 + P338 + P310
Flash Point Not applicable
Risk Codes 37/38-41-52
Safety Statements 26-39
RTECS Number BD1700000
Transport Information UN3260 8/PG III
WGK Germany 1
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 10/06/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Aluminum Sulfate (Anhydrous)

Product Number: All applicable American Elements product codes, e.g. AL-SAT-02-C.AHYD , AL-SAT-03-C.AHYD , AL-SAT-04-C.AHYD , AL-SAT-05-C.AHYD

CAS #: 10043-01-3

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

GHS Classification in accordance with 29 CFR 1910 (OSHA HCS)
Corrosive to metals (Category 1), H290
Serious eye damage (Category 1), H318

GHS Label elements, including precautionary statements
Hazard pictogram

Corrosion - GHS05

GHS05
Signal word
Danger
Hazard statements
Hazard statement(s)
H290 May be corrosive to metals.
H318 Causes serious eye damage.
Precautionary statement(s)
P234 Keep only in original container.
P280 Wear eye protection/ face protection.
P305 + P351 + P338 + P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing. Immediately
call a POISON CENTER/doctor.
P390 Absorb spillage to prevent material damage.
P406 Store in corrosive resistant container with a resistant inner liner.

Hazards not otherwise classified (HNOC) or not covered by GHS - none


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substances
CAS No. / Substance Name: 10043-01-3 Aluminum sulfate
Identification number(s):
EC number: 233-135-0


SECTION 4. FIRST AID MEASURES

Description of first aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.Move out of dangerous area.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Consult a physician.
In case of eye contact
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
If swallowed
Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11
Indication of any immediate medical attention and special treatment needed
No data available


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Special hazards arising from the substance or mixture
No data available
Wear self-contained breathing apparatus for firefighting if necessary.
Further information
No data available


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Wear respiratory protection. Avoid dust formation. Avoid breathing Vapors, mist or gas. Ensure adequate ventilation.
Evacuate personnel to safe areas. Avoid breathing dust.
For personal protection see section 8.
Environmental precautions
Do not let product enter drains.
Methods and materials for containment and cleaning up
Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
Reference to other sections
For disposal see section 13.


SECTION 7. HANDLING AND STORAGE

Precautions for safe handling
Avoid formation of dust and aerosols.Further processing of solid materials may result in the formation of combustible dusts. The potential for combustible dust formation should be taken into consideration before additional processing occurs.
Provide appropriate exhaust ventilation at places where dust is formed.
For precautions see section 2.
Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Hygroscopic: Store under inert gas. Keep in a dry place.
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Control parameters
Components with workplace control parameters
Component: Aluminum Sulfate
CAS-No.: 10043-01-3
Value: TWA
Control parameters: 2.000000 mg/m3
Basis: USA. NIOSH Recommended Exposure Limits
Value: TWA
Control parameters: 2 mg/m3
Basis: USA. NIOSH Recommended Exposure Limits
Value: PEL
Control parameters: 2.000000 mg/m3
Basis: California permissible exposure limits for chemical contaminants (Title 8, Article 107)
Exposure controls
Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Personal protective equipment
Eye/face protection
Face shield and safety glasses Use equipment for eye protection tested and approved under appropriate
government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
Body Protection
Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face particle respirator type N100 (US) or type P3 (EN 143) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Control of environmental exposure
Do not let product enter drains.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

"Information on basic physical and chemical properties
Appearance:
Form: White Powder
Odor: No data available
Odor threshold: No data available.
pH (50 g/l) at 20 °C (68 °F): 3.5
Melting point/Melting range: 770 °C (1418 °F)
Boiling point/Boiling range: No data available
Sublimation temperature / start: No data available
Flammability (solid, gas): No data available.
Ignition temperature: No data available
Decomposition temperature: No data available
Autoignition: No data available.
Danger of explosion: No data available.
Explosion limits:
Lower: No data available
Upper: No data available
Vapor pressure: N/A
Density at 20 °C (68 °F): 2.71 g/cm3
Relative density: No data available.
Vapor density: N/A
Evaporation rate: N/A
Solubility in Water (H2O): 1.0 g/l at (20 °C) - completely miscible
Partition coefficient (n-octanol/water): No data available.
Viscosity:
Dynamic: N/A
Kinematic: N/A
Other information:
Surface tension 73 mN/m at 20 °C (68 °F)


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
No data available
Conditions to avoid
Air Exposure to moisture
Incompatible materials
Incompatible with strong bases and oxidizing agents., Ammonia, Water, Amines
Hazardous decomposition products
Hazardous decomposition products formed under fire conditions. - Sulphur oxides, Aluminum oxide
Other decomposition products - No data available
In the event of fire: see section 5


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity
LD50 Oral - Rat - male and female - > 5,000 mg/kg
(OECD Test Guideline 401)
Inhalation: No data available
Dermal: No data available
No data available
Skin corrosion/irritation
Skin - Rabbit
Result: No skin irritation - 4 h
(OECD Test Guideline 404)
Serious eye damage/eye irritation
Eyes - Rabbit
Result: Irritating to eyes.
(OECD Test Guideline 405)
Respiratory or skin sensitisation
No data available
Germ cell mutagenicity
Ames test
S. typhimurium
Result: negative
Rat
Cytogenetic analysis
Carcinogenicity
IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC.
NTP: No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP.
OSHA: No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen by OSHA.
Reproductive toxicity
No data available
Reproductive toxicity - Rat - Intratesticular
Paternal Effects: Spermatogenesis (including genetic material, sperm morphology,motility, and count).
Paternal Effects: Testes, epididymis, sperm duct.
Reproductive toxicity - Mouse - Intraperitoneal
Effects on Newborn: Growth statistics (e.g., reduced weight gain). Effects on Newborn: Behavioral.
No data available
Specific target organ toxicity - single exposure
No data available
Specific target organ toxicity - repeated exposure
No data available
Aspiration hazard
No data available
Additional Information
RTECS: BD1700000
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly
investigated.
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly
investigated.
Stomach - Irregularities - Based on Human Evidence
Stomach - Irregularities - Based on Human Evidence


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
Toxicity to daphnia and other aquatic invertebrates
LC50 - Daphnia magna (Water flea) - 38.2 mg/l - 48 h
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
Other adverse effects
No data available


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Product
Offer surplus and non-recyclable solutions to a licensed disposal company. Contact a licensed professional waste
disposal service to dispose of this material.
Contaminated packaging
Dispose of as unused product.


SECTION 14. TRANSPORT INFORMATION

DOT (US)
UN number: 3260 Class: 8 Packing group: III
Proper shipping name: Corrosive solid, acidic, inorganic, n.o.s. (Aluminum sulphate)
Reportable Quantity (RQ): 5000 lbs
Poison Inhalation Hazard: No
IMDG
UN number: 3260 Class: 8 Packing group: III EMS-No: F-A, S-B
Proper shipping name: CORROSIVE SOLID, ACIDIC, INORGANIC, N.O.S. (Aluminum sulphate)
IATA
UN number: 3260 Class: 8 Packing group: III
Proper shipping name: Corrosive solid, acidic, inorganic, n.o.s. (Aluminum sulphate)


SECTION 15. REGULATORY INFORMATION

SARA 302 Components
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards
Acute Health Hazard, Chronic Health Hazard
Massachusetts Right To Know Components
Aluminum sulphate
CAS-No.
10043-01-3
Revision Date
1993-04-24
Pennsylvania Right To Know Components
Aluminum sulphate
CAS-No.
10043-01-3
Revision Date
1993-04-24
New Jersey Right To Know Components
Aluminum sulphate
CAS-No.
10043-01-3
Revision Date
1993-04-24
California Prop. 65 Components
This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Aluminum Sulfate (Anhydrous)

High purity Aluminum Sulfate AnhydrousAnhydrous Aluminum Sulfate is a moderately water and acid soluble Aluminum source for uses compatible with sulfates. Sulfate compounds are salts or esters of sulfuric acid formed by replacing one or both of the hydrogens with a metal. Most metal sulfate compounds are readily soluble in water for uses such as water treatment, unlike fluorides and oxides which tend to be insoluble. Organometallic forms are soluble in organic solutions and sometimes in both aqueous and organic solutions. Metallic ions can also be dispersed utilizing suspended or coated nanoparticles and deposited utilizing sputtering targets and evaporation materials for uses such as solar cells and fuel cells. Aluminum Sulfate is generally immediately available in most volumes. High purity, submicron and nanopowder forms may be considered. We also produce Aluminum Sulfate Solution. American Elements produces to many standard grades when applicable, including Mil Spec (military grade); ACS, Reagent and Technical Grade; Food, Agricultural and Pharmaceutical Grade; Optical Grade, USP and EP/BP (European Pharmacopoeia/British Pharmacopoeia) and follows applicable ASTM testing standards. Typical and custom packaging is available. Additional technical, research and safety (MSDS) information is available as is a Reference Calculator for converting relevant units of measurement.

Aluminum Sulfate (Anhydrous) Synonyms

Aluminum alum, Alum, Dialuminum sulfate, Pickle Alum, Cake alum, Papermaker's Alum, Pearl Alum, Filter Alum, Aluminium sulphate anhydrous, Alumen Aluminium sulfate, aluminium sulphate, Aluminium trisulfate, Aluminum sesquisulfate, Aluminum sulfate (2:3), Aluminum trisulfate, Aluminum(III) sulfate, Alunogenite, Dialuminum sulfate, Fertosan

Chemical Identifiers

Linear Formula Al2(SO4)3
MDL Number MFCD00003423
EC No. 233-135-0
Beilstein/Reaxys No. N/A
Pubchem CID 24850
IUPAC Name dialuminum trisulfate
SMILES [Al+3].[Al+3].[O-]S(=O)(=O)[O-].[O-]S([O-])(=O)=O.[O-]S([O-])(=O)=O
InchI Identifier InChI=1S/2Al.3H2O4S/c;;3*1-5(2,3)4/h;;3*(H2,1,2,3,4)/q2*+3;;;/p-6
InchI Key DIZPMCHEQGEION-UHFFFAOYSA-H

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

Aluminum

See more Aluminum products. Aluminum (or Aluminium) (atomic symbol: Al, atomic number: 13) is a Block P, Group 13, Period 3 element with an atomic weight of 26.9815386. It is the third most abundant element in the earth's crust and the most abundant metallic element. Aluminum Bohr Model Aluminum's name is derived from alumina, the mineral from which Sir Humphrey Davy attempted to refine it from in 1812. Aluminum was first predicted by Antoine Lavoisier 1787 and first isolated by Hans Christian Øersted in 1825. Aluminum is a silvery gray metal that possesses many desirable characteristics. It is light, nonmagnetic and non-sparking. It stands second among metals in the scale of malleability, and sixth in ductility. It is extensively used in many industrial applications where a strong, light, easily constructed material is needed. Elemental AluminumAlthough it has only 60% of the electrical conductivity of copper, it is used in electrical transmission lines because of its light weight. Pure aluminum is soft and lacks strength, but alloyed with small amounts of copper, magnesium, silicon, manganese, or other elements, it imparts a variety of useful properties.

Sulfur

See more Sulfur products. Sulfur (or Sulphur) (atomic symbol: S, atomic number: 16) is a Block P, Group 16, Period 3 element with an atomic radius of 32.066. Sulfur Bohr ModelThe number of electrons in each of Sulfur's shells is 2, 8, 6 and its electron configuration is [Ne] 3s2 3p4. In its elemental form, sulfur has a light yellow appearance. The sulfur atom has a covalent radius of 105 pm and a Van der Waals radius of 180 pm. In nature, sulfur can be found in hot springs, meteorites, volcanoes, and as galena, gypsum, and epsom salts. Sulfur has been known since ancient times but was not accepted as an element until 1777, when Antoine Lavoisier helped to convince the scientific community that it was an element and not a compound.

TODAY'S TOP DISCOVERY!

October 06, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
Researchers develop AINU (AI) to detect cancer and viral infections with nanoscale precision

Researchers develop AINU (AI) to detect cancer and viral infections with nanoscale precision