Diiron Boride Sputtering Target

CAS #:

Linear Formula:

Fe2B

MDL Number:

MFCD00016092

EC No.:

234-490-4

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Iron Boride (Fe2B) Sputtering Target
FE2-B-02-ST
Pricing > SDS > Data Sheet >
(3N) 99.9% Iron Boride (Fe2B) Sputtering Target
FE2-B-03-ST
Pricing > SDS > Data Sheet >
(4N) 99.99% Iron Boride (Fe2B) Sputtering Target
FE2-B-04-ST
Pricing > SDS > Data Sheet >
(5N) 99.999% Iron Boride (Fe2B) Sputtering Target
FE2-B-05-ST
Pricing > SDS > Data Sheet >

Diiron Boride Sputtering Target Properties (Theoretical)

Compound Formula BFe2
Molecular Weight 122.501
Appearance Refractory Solid
Melting Point N/A
Boiling Point N/A
Density 7.15 g/cm3
Solubility in H2O Insoluble
Exact Mass 122.87918 g/mol
Monoisotopic Mass 122.878997802734 Da
Charge N/A

Diiron Boride Sputtering Target Health & Safety Information

Signal Word N/A
Hazard Statements N/A
Hazard Codes N/A
Risk Codes N/A
Safety Statements N/A
Transport Information NONH for all modes of transport
WGK Germany 3

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 10/14/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Diiron Boride Sputtering Target

Product Number: All applicable American Elements product codes, e.g. FE2-B-02-ST , FE2-B-03-ST , FE2-B-04-ST , FE2-B-05-ST

CAS #: 12006-85-8

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification
Classification under 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Label Elements
None required
Hazards not otherwise classified (HNOC)
None identified


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Component
Iron boride (Fe2B)
Cas No.: 12006-85-8


SECTION 4. FIRST AID MEASURES

Eye Contact Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
Skin Contact Wash off immediately with plenty of water for at least 15 minutes. Get medical attention immediately if symptoms occur.
Inhalation Remove to fresh air. Get medical attention immediately if symptoms occur.
Ingestion Clean mouth with water and drink afterwards plenty of water. Get medical attention if
symptoms occur.
Most important symptoms and effects
None reasonably foreseeable.
Notes to Physician Treat symptomatically


SECTION 5. FIREFIGHTING MEASURES

Suitable Extinguishing Media Not combustible.
Unsuitable Extinguishing Media No information available
Flash Point No information available
Method - No information available
Autoignition Temperature No information available
Explosion Limits
Upper No data available
Lower No data available
Sensitivity to Mechanical Impact No information available
Sensitivity to Static Discharge No information available
Specific Hazards Arising from the Chemical
Keep product and empty container away from heat and sources of ignition.
Hazardous Combustion Products
Oxides of boron. Iron oxides.
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal Precautions Ensure adequate ventilation. Use personal protective equipment as required. Avoid dust formation.
Environmental Precautions Should not be released into the environment. See Section 12 for additional Ecological Information. Do not allow material to contaminate ground water system. Do not flush into surface water or sanitary sewer system.
Methods for Containment and Clean Up
Sweep up and shovel into suitable containers for disposal. Avoid dust formation.


SECTION 7. HANDLING AND STORAGE

Handling Wear personal protective equipment/face protection. Ensure adequate ventilation. Avoid
contact with skin, eyes or clothing. Avoid ingestion and inhalation. Avoid dust formation.
Storage Keep containers tightly closed in a dry, cool and well-ventilated place.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Engineering Measures None under normal use conditions.
Personal Protective Equipment
Eye/face Protection Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin and body protection Wear appropriate protective gloves and clothing to prevent skin exposure.
Respiratory Protection No protective equipment is needed under normal use conditions.
Hygiene Measures Handle in accordance with good industrial hygiene and safety practice.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Physical State Solid
Appearance No information available
Odor Odorless
Odor Threshold No information available
pH No information available
Melting Point/Range No data available
Boiling Point/Range No information available
Flash Point No information available
Evaporation Rate Not applicable
Flammability (solid,gas) No information available
Flammability or explosive limits
Upper No data available
Lower No data available
Vapor Pressure No information available
Vapor Density Not applicable
Specific Gravity 7.3 g/cm3
Solubility No information available
Partition coefficient; n-octanol/water No data available
Autoignition Temperature No information available
Decomposition Temperature No information available
Viscosity Not applicable
Molecular Formula Fe2 B
Molecular Weight 122.50


SECTION 10. STABILITY AND REACTIVITY

Reactive Hazard None known, based on information available
Stability Stable under normal conditions.
Conditions to Avoid Incompatible products.
Incompatible Materials Oxidizing agent
Hazardous Decomposition ProductsOxides of boron, Iron oxides
Hazardous Polymerization Hazardous polymerization does not occur.
Hazardous Reactions None under normal processing.


SECTION 11. TOXICOLOGICAL INFORMATION

Acute Toxicity
Product Information
Component Information
Toxicologically Synergistic
Products
No information available
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Irritation No information available
Sensitization No information available
Mutagenic Effects No information available
Reproductive Effects No information available.
Developmental Effects No information available.
Teratogenicity No information available.
STOT - single exposure None known
STOT - repeated exposure None known
Aspiration hazard No information available
Symptoms / effects,both acute and delayed
No information available
Endocrine Disruptor Information No information available
Other Adverse Effects The toxicological properties have not been fully investigated.


SECTION 12. ECOLOGICAL INFORMATION

Ecotoxicity
May cause long-term adverse effects in the environment. Do not allow material to contaminate ground water system.
Persistence and Degradability Insoluble in water May persist
Bioaccumulation/ Accumulation No information available.
Mobility Is not likely mobile in the environment due its low water solubility.


SECTION 13. DISPOSAL CONSIDERATIONS

Waste Disposal Methods Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. Chemical waste generators must also consult local, regional, and national hazardous waste regulations to ensure complete and accurate classification.


SECTION 14. TRANSPORT INFORMATION

DOT Not regulated
TDG Not regulated
IATA Not regulated
IMDG/IMO Not regulated


SECTION 15. REGULATORY INFORMATION

U.S. Federal Regulations
SARA 313 Not applicable
SARA 311/312 Hazard Categories See section 2 for more information
CWA (Clean Water Act) Not applicable
Clean Air Act Not applicable
OSHA - Occupational Safety and
Health Administration
Not applicable
CERCLA Not applicable
California Proposition 65 This product does not contain any Proposition 65 chemicals.
U.S.
DOT Severe Marine Pollutant N
U.S. Department of Homeland Security
This product does not contain any DHS chemicals.
Other International Regulations
Mexico - Grade No information available


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Diiron Boride Sputtering Target

American Elements specializes in producing high purity Diiron Boride Sputtering Targets with the highest possible density High Purity (99.99%) Diiron Boride Sputtering Targetand smallest possible average grain sizes for use in semiconductor, chemical vapor deposition (CVD) and physical vapor deposition (PVD) display and optical applications. Our standard sputtering targets for thin film deposition are available monoblock or bonded with planar target dimensions and configurations up to 820 mm with hole drill locations and threading, beveling, grooves and backing designed to work with both older sputtering devices as well as the latest process equipment, such as large area coating for solar energy or fuel cells and flip-chip applications. Rotary (cylindrical), round, rectangular, square, ring, annular, oval, "dog-bone" and other shaped targets are available in standard, custom, and research sized dimensions. All targets are analyzed using best demonstrated techniques including X-Ray Fluorescence (XRF), Glow Discharge Mass Spectrometry (GDMS), and Inductively Coupled Plasma (ICP). Materials are produced using crystallization, solid state and other ultra high purification processes such as sublimation. American Elements specializes in producing custom compositions for commercial and research applications and for new proprietary technologies. Please request a quote above for more information on lead time and pricing.

Diiron Boride Sputtering Target Synonyms

Diiron monoboride, iron(I) boride

Chemical Identifiers

Linear Formula Fe2B
MDL Number MFCD00016092
EC No. 234-490-4
Beilstein/Reaxys No. N/A
Pubchem CID 6336853
IUPAC Name boron; iron
SMILES B.[Fe].[Fe]
InchI Identifier InChI=1S/B.2Fe
InchI Key FSDZRQFSRALZQJ-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Payment Methods

American Elements accepts checks, wire transfers, ACH, most major credit and debit cards (Visa, MasterCard, AMEX, Discover) and Paypal.

For the convenience of our international customers, American Elements offers the following additional payment methods:

SOFORT bank tranfer payment for Austria, Belgium, Germany and SwitzerlandJCB cards for Japan and WorldwideBoleto Bancario for BraziliDeal payments for the Netherlands, Germany, Austria, Belgium, Italy, Poland, Spain, Switzerland, and the United KingdomGiroPay for GermanyDankort cards for DenmarkElo cards for BrazileNETS for SingaporeCartaSi for ItalyCarte-Bleue cards for FranceChina UnionPayHipercard cards for BrazilTROY cards for TurkeyBC cards for South KoreaRuPay for India

Related Elements

Boron

See more Boron products. Boron Bohr ModelBoron (atomic symbol: B, atomic number: 5) is a Block P, Group 13, Period 2 element with an atomic weight of 10.81. The number of electrons in each of boron's shells is 2, 3 and its electron configuration is [He] 2s2 2p1. The boron atom has a radius of 90 pm and a Van der Waals radius of 192 pm. Boron was discovered by Joseph Louis Gay-Lussac and Louis Jacques Thénard in 1808 and was first isolated by Humphry Davy later that year. Boron is classified as a metalloid is not found naturally on earth. Elemental BoronAlong with carbon and nitrogen, boron is one of the few elements in the periodic table known to form stable compounds featuring triple bonds. Boron has an energy band gap of 1.50 to 1.56 eV, which is higher than that of either silicon or germanium. The name Boron originates from a combination of carbon and the Arabic word buraqu meaning borax.

Iron

See more Iron products. Iron (atomic symbol: Fe, atomic number: 26) is a Block D, Group 8, Period 4 element with an atomic weight of 55.845. The number of electrons in each of Iron's shells is 2, 8, 14, 2 and its electron configuration is [Ar] 3d6 4s2. Iron Bohr ModelThe iron atom has a radius of 126 pm and a Van der Waals radius of 194 pm. Iron was discovered by humans before 5000 BC. In its elemental form, iron has a lustrous grayish metallic appearance. Iron is the fourth most common element in the Earth's crust and the most common element by mass forming the earth as a whole. Iron is rarely found as a free element, since it tends to oxidize easily; it is usually found in minerals such as magnetite, hematite, goethite, limonite, or siderite.Elemental Iron Though pure iron is typically soft, the addition of carbon creates the alloy known as steel, which is significantly stronger.

TODAY'S TOP DISCOVERY!

October 14, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
Researchers develop AINU (AI) to detect cancer and viral infections with nanoscale precision

Researchers develop AINU (AI) to detect cancer and viral infections with nanoscale precision