20th anniversary seal20th anniversary seal20th anniversary seal

Platinum Conductor Paste

CAS #:

Linear Formula:

Pt

MDL Number:

MFCD00011179

EC No.:

231-116-1

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
Platinum Conductor Paste
PT-M-01-PST
Pricing > SDS > Data Sheet >
Question? Ask an American Elements EngineerWHOLESALE/SKU 0000-742-6798

Platinum Conductor Paste Properties

Molecular Weight

195.08

Appearance

Gray paste

Melting Point

1772 °C

Boiling Point

3827   °C

Density (Theoretical)

21.45 g/cm3

Tensile Strength

N/A

Thermal Conductivity

0.716 W/cm/K

Electrical Resistivity

10.6 µÎ©-cm (20 °C)

Electronegativity

2.2 Paulings

Specific Heat

0.0317 Cal/g/K @ 25 °C

Heat of Vaporization

122 K-Cal/gm atom at 3827 °C

Platinum Conductor Paste Health & Safety Information

Signal Word N/A
Hazard Statements N/A
Hazard Codes N/A
Risk Codes N/A
Safety Statements N/A
Transport Information N/A
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Created: 5/15/2015
Date Revised: 5/15/2015

SECTION 1. IDENTIFICATION

Product Name: Platinum Conductor Paste

Product Number: All applicable American Elements product codes, e.g. PT-M-01-PST

Relevant identified uses of the substance: Scientific research and development


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture
GHS Classification in accordance with 29 CFR 1910 (OSHA HCS)
Flammable liquids(Category 4), H227
Skin irritation(Category 2), H315
Serious eye damage(Category 1), H318
Respiratory sensitisation(Category 1), H334
Skin sensitisation(Category 1), H317
Specific target organ toxicity -single exposure(Category 3), Respiratory system, H335
For the full text of the H-Statements mentioned in this Section, see Section 16.
GHS Label elements, including precautionary statements
Pictogram

Corrosion - GHS05 Exclamation Mark - GHS07 Health Hazard - GHS08

Signal word
Danger
Hazard statement(s)
H227
Combustible liquid.
H315
Causes skin irritation.
H317
May cause an allergic skin reaction.
H318
Causes serious eye damage.
H334
May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335
May cause respiratory irritation.
Precautionary statement(s)
P210
Keep away from heat/sparks/open flames/hot surfaces. -No smoking.
P261
Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
P264
Wash skin thoroughly after handling.
P271
Use only outdoors or in a well-ventilated area.
P272
Contaminated work clothing should not be allowed out of the workplace.
P280
Wear protective gloves/ eye protection/ face protection.
P285
In case of inadequate ventilation wear respiratory protection.
P302 + P352
IF ON SKIN: Wash with plenty of soap and water.
P304 + P340 + P312
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/ physician if you feel unwell.
P305 + P351 + P338 + P310
IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor/ physician.
P333 + P313
If skin irritation or rash occurs: Get medical advice/ attention.
P342 + P311
If experiencing respiratory symptoms: Call a POISON CENTER or doctor/ physician.
P362
Take off contaminated clothing and wash before reuse.
P370 + P378
In case of fire: Use dry sand, dry chemical or alcohol-resistant foam for extinction.
P403 + P233
Store in a well-ventilated place. Keep container tightly closed.
P403 + P235
Store in a well-ventilated place. Keep cool.
P405
Store locked up.
P501
Dispose of contents/ container to an approved waste disposal plant.
Hazards not otherwise classified (HNOC) or not covered by GHS-none


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Synonyms:
Dyesol(R) PT1 platinum paste
Pt paste
conductive paste
Hazardous Components
α-Terpineol
CAS-No. 98-55-5
EC-No. 233-986-8
Skin Irrit. 2; Eye Irrit. 2A; STOT SE 3; H315, H319, H335
>=90-<=100%
Cellulose, ethyl ether
CAS-No. 9004-57-3
>=10-<20%
Hexachloroplatinic acid hydrate
CAS-No. 26023-84-7
EC-No. 241-010-7
Index-No. 078-009-00-4
Acute Tox. 3; Skin Corr.1B; Eye Dam.1; Resp. Sens.1; Skin Sens.1; H301, H314, H317, H318, H334
>=1-<5%


SECTION 4. FIRST AID MEASURES

Description of first aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
Move out of dangerous area.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Consult a physician.
In case of eye contact
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
Continue rinsing eyes during transport to hospital.
If swallowed
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11
Indication of any immediate medical attention and special treatment needed
No data available


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Special hazards arising from the substance or mixture
Carbon oxides, Hydrogen chloride gas
Advice for firefighters
Wear self-contained breathing apparatus for firefighting if necessary.
Further information
Use water spray to cool unopened containers.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapours accumulating to form explosive concentrations. Vapours can accumulate in low areas.
For personal protection see section 8.
Environmental precautions
Prevent further leakage or spillage if safe to do so. Do not let product enter drains.
Methods and materials for containment and cleaning up
Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and place in container for disposal according to local regulations (see section 13). Keep in suitable, closed containers for disposal.
Reference to other sections
For disposal see section 13.


SECTION 7. HANDLING AND STORAGE

Precautions for safe handling
Avoid contact with skin and eyes. Avoid inhalation of vapour or mist.
Keep away from sources of ignition -No smoking. Take measures to prevent the build up of electrostatic charge.
For precautions see section 2.
Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Containers which are opened must be carefully resealed and kept upright to prevent leakage.
Recommended storage temperature
2 -8 °C
Store in the dark.
Storage class (TRGS 510):
Combustible liquids
Specific end use(s)
Apart from the uses mentioned in section 1 no other specific uses are stipulated


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Control parameters
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
Exposure controls
Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Personal protective equipment
Eye/face protection
Tightly fitting safety goggles. Faceshield (8-inch minimum). Use equipment for eye
protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
Body Protection
Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls.
If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Control of environmental exposure
Prevent further leakage or spillage if safe to do so. Do not let product enter drains.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance
Form: liquid
Colour: amber
Odour
characteristic
Odour Threshold
No data available
pH
No data available
Melting point/freezing point
No data available
Initial boiling point and boiling range
214 -224 °C (417 -435 °F)
Flash point
90 °C (194 °F)
Evaporation rate
No data available
Flammability (solid, gas)
No data available
Upper/lower flammability or explosive limits
No data available
Vapour pressure
No data available
Vapour density
No data available
Relative density
No data available
Water solubility
No data available
Partition coefficient: n-octanol/water
No data available
Auto-ignition temperature
No data available
Decomposition temperature
No data available
Viscosity
No data available
Explosive properties
No data available
Oxidizing properties
No data available
Other safety information
No data available


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
No data available
Conditions to avoid
Heat, flames and sparks.
Incompatible materials
Strong acids and strong bases, Strong oxidizing agents
Hazardous decomposition products
Other decomposition products-No data available
In the event of fire: see section 5


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity
No data available
Inhalation: No data available
Dermal: No data available
No data available
Skin corrosion/irritation
No data available
Serious eye damage/eye irritation
No data available
Respiratory or skin sensitisation
No data available
Germ cell mutagenicity
No data available
Carcinogenicity
IARC:
No component of this product present at levels greater than or equal to 0.1% is identified as
probable, possible or confirmed human carcinogen by IARC.
ACGIH:
No component of this product present at levels greater than or equal to 0.1% is identified as a
carcinogen or potential carcinogen by ACGIH.
NTP:
No component of this product present at levels greater than or equal to 0.1% is identified as a
known or anticipated carcinogen by NTP.
OSHA:
No component of this product present at levels greater than or equal to 0.1% is identified as a
carcinogen or potential carcinogen by OSHA.
Reproductive toxicity
No data available
No data available
Specific target organ toxicity -single exposure
No data available
Specific target organ toxicity -repeated exposure
No data available
Aspiration hazard
No data available
Additional Information
RTECS: Not available
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
No data available
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
Other adverse effects
No data available


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Product
This combustible material may be burned in a chemical incinerator equipped with an afterburner and scrubber.
Offer surplus and non-recyclable solutions to a licensed disposal company.
Contact a licensed professional waste disposal service to dispose of this material.
Contaminated packaging
Dispose of as unused product.


SECTION 14. TRANSPORT INFORMATION

DOT (US)
NA-Number: 1993
Class: NONE
Packing group: III
Proper shipping name: Combustible liquid, n.o.s.(α-Terpineol)
Reportable Quantity
(RQ):
Poison Inhalation Hazard: No
IMDG
Not dangerous goods
IATA
Not dangerous goods


SECTION 15. REGULATORY INFORMATION

SARA 302 Components
No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.
SARA 313 Components
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SARA 311/312 Hazards
Fire Hazard, Acute Health Hazard
Massachusetts Right To Know Components
No components are subject to the Massachusetts Right to Know Act.
Pennsylvania Right To Know Components
α-Terpineol
CAS-No.
98-55-5
Revision Date
Cellulose, ethyl ether
9004-57-3
Hexachloroplatinic acid hydrate
26023-84-7
2007-03-01
New Jersey Right To Know Components
α-Terpineol
CAS-No.
98-55-5
Revision Date
Cellulose, ethyl ether
9004-57-3
Hexachloroplatinic acid hydrate
26023-84-7
2007-03-01
California Prop. 65 Components
This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.


16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2016 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Platinum Conductor Paste

Platinum Conductor Paste is a screen-printable electrode material for use in solid oxide fuel cells (SOFCs) and sensors. Platinum paste is generally immediately available in most volumes, including bulk orders. American Elements can produce materials to custom specifications by request, in addition to custom compositions for commercial and research applications and new proprietary technologies. American Elements also casts any of the rare earth metals and most other advanced materials into rod, bar or plate form, as well as numerous other machined shapes and in the form of solutions and organometallic compounds. Ultra high purity and high purity forms also include metal powder, submicron powder and nanomaterials, targets for thin film deposition, and pellets for chemical vapor deposition (CVD) and physical vapor deposition (PVD) applications. American Elements produces to many standard grades when applicable, including Mil Spec (military grade); ACS, Reagent and Technical Grade; Food, Agricultural and Pharmaceutical Grade; Optical Grade, USP and EP/BP (European Pharmacopoeia/British Pharmacopoeia) and follows applicable ASTM testing standards. Typical and custom packaging is available, as is additional research, technical and safety (MSDS) data. Please contact us for information on lead time and pricing above.

Platinum Conductor Paste Synonyms

N/A

Platinum Conductor Paste Chemical Identifiers

Linear Formula

Pt

Pubchem CID

23939

MDL Number

MFCD00011179

EC No.

231-116-1

Beilstein Registry No.

N/A

SMILES

[Pt]

InchI Identifier

InChI=1S/Pt

InchI Key

BASFCYQUMIYNBI-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

See more Platinum products. Platinum (atomic symbol: Pt, atomic number: 78) is a Block D, Group 10, Period 6 element with an atomic weight of 195.084. The number of electrons in each of platinum's shells is [2, 8, 18, 32, 17, 1] and its electron configuration is [Xe] 4f14 5d9 6s1. The platinum atom has a radius of 139 pm and a Van der Waals radius of 175 pm. Platinum Bohr ModelElemental PlatinumPlatinum was discovered and first isolated by Antonio de Ulloa in 1735. It is one of the rarest elements in the earth's crust, occurring at a concentration of only 0.005 ppm. Platinum is found uncombined as a free element and alloyed with iridium as platiniridium. In its elemental form, platinum has a grayish white appearance. It is highly resistant to corrosion: the metal does not oxidize in air at any temperature. It is generally non-reactive, even at high temperatures. The origin of the name "platinum" comes from the Spanish word platina, meaning silver.

TODAY'S SCIENCE POST!

November 23, 2017
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day

London's buses will soon be fueled by recycled coffee grounds