Safety Data Sheet

SAFETY DATA SHEET

Date Accessed: 05/02/2024
Date Revised: 01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Yttrium Silicide

Product Number: All applicable American Elements product codes, e.g. Y-SID-02 , Y-SID-03 , Y-SID-04 , Y-SID-05

CAS #: 12067-55-9

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Hazard Statements:
H228: Flammable solid
H315 Causes skin irritation
H319 Causes serious eye irritation
H335: May cause respiratory irritation

Flame - GHS02 Exclamation Mark - GHS07

Precautionary Statements:
P210: Keep away from heat/sparks/open flames/hot surfaces – No smoking
P261 Avoid breathing dust/fume/vapor
P280: Wear protective gloves/protective clothing/eye protection/face protection
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
P405: Store locked up
P501: Dispose of contents/container in accordance with local/regional/national/international regulations

HMIS Health Ratings (0-4):
Health: 1 (Powder), 0 (Bulk)
Flammability: 2 (Powder), 0 (Bulk)
Physical: 2 (Powder), 0 (Bulk)


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Family: Ceramic
Additional Names: None
Yttrium silicide (YSi2):
Percentage: 100 wt%
CAS #: 12067-55-9
EC #: 235-080-8


SECTION 4. FIRST AID MEASURES

General Treatment: Seek medical attention if symptoms persist.
Special Treatment: None
Important Symptoms: None
Inhalation: Remove victim to fresh air. Supply oxygen if breathing is difficult.
Ingestion: Seek medical attention.
Skin: Wash affected area with mild soap and water. Remove any contaminated clothing.
Eyes: Flush eyes with water, blinking often for several minutes. Remove contact lenses if present and easy to do. Continue rinsing


SECTION 5. FIREFIGHTING MEASURES

Flammability: Non-flammable, except as powder

Extinguishing Media: Do not use water for metal fires – use CO2, sand, extinguishing powder.

Spec. Fire Fighting Procedure: Use full-face, self-contained breathing apparatus with full protective
clothing to prevent contact with skin and eyes. See section 10 for decomposition products.


SECTION 6. ACCIDENTAL RELEASE MEASURES

If Material Is Released/Spilled: Wear appropriate respiratory and protective equipment specified in
special protection information. Isolate spill area and provide ventilation. Vacuum up spill using a high efficiency particulate absolute (HEPA) air filter and place in a closed container for disposal.
Take care not to raise dust.

Environmental Precautions: Isolate runoff to prevent environmental pollution.


SECTION 7. HANDLING AND STORAGE

Handling Conditions: Handle under dry protective gas. Wash thoroughly after handling.

Storage Conditions: Store in a cool dry place in a tightly sealed container. Store under dry inert gas. Store apart from materials and conditions listed in section 10.

Work/Hygienic Maintenance: Do not use tobacco or food in work area. Wash thoroughly before
eating and smoking. Do not blow dust off clothing or skin with compressed air.

Ventilation: Provide sufficient ventilation to maintain concentration at or below threshold limit.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Permissible Exposure Limits: 1 mg/m3 as Y, long-term value
Threshold Limit Value: 1 mg/m3 as Y, long-term value

Special Equipment: None

Respiratory Protection: Use a respirator with type N95 (USA) or PE (EN 143) cartridges as a backup to engineering controls. Risk assessment should be performed to determine if purifying respirators are appropriate. Only use equipment tested and approved under appropriate government standards.

Protective Gloves: Nitrile rubber, NBR 0.11mm thick.

Eye Protection: Safety glasses or goggles

Body Protection: Protective work clothing. Wear close-toed shoes and long sleeves/pants.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Color Grey
Form: Powder, Granules, Pellets, Sputtering target, Custom parts
Odor: Odorless
Water Solubility: Insoluble
Boiling Point: N/A
Melting Point: 1760 °C
Flash Point: N/A
Autoignition Temperature: N/A
Density: 4.39 g/cc
Molecular weight: 145.08 g/mol


SECTION 10. STABILITY AND REACTIVITY

Stability: Stable under recommended storage conditions
Reacts With: Halogens, Interhalogens, Oxidizing agents
Incompatible Conditions: Air, Water/moisture
Hazardous Decomposition Products: Metal oxide fume


SECTION 11. TOXICOLOGICAL INFORMATION

Potential Health Effects
Eyes: May cause irritation
Skin: May cause irritation
Ingestion: May cause irritation
Inhalation: May cause irritation
Chronic: N/A

Signs & Symptoms: N/A

Aggravated Medical Conditions: N/A

Median Lethal Dose: 3160 mg/kg for rat by mouth

Carcinogen: N/A


SECTION 12. ECOLOGICAL INFORMATION

Aquatic Toxicity: Low
Persistent Bioaccumulation Toxicity: No
Very Persistent, Very Bioaccumulative: No
Notes: N/A


SECTION 13. DISPOSAL CONSIDERATIONS

Dispose of in accordance with local, state, national, and international regulations.


SECTION 14. TRANSPORT INFORMATION

Hazardous: Hazardous as powder only.
Hazard Class: 4.1 Flammable solids, self-reactive substances and solid desensitized explosives
Packing Group: II
UN Number: UN3178
Proper Shipping Name: Flammable solid, inorganic, n.o.s. (Yttrium silicide)


SECTION 15. REGULATORY INFORMATION

Sec 302 Extremely Hazardous: No
Sec 304 Reportable Quantities: N/A
Sec 313 Toxic Chemicals: No