20th anniversary seal20th anniversary seal20th anniversary seal

Antimony Tin Oxide Nanoparticles

CAS #:

Linear Formula:

Sb2SnO5

MDL Number:

MFCD00799153

EC No.:

N/A

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Antimony Tin Oxide Nanoparticles
SB-SNO-02-NP
Pricing > SDS > Data Sheet >
(3N) 99.9% Antimony Tin Oxide Nanoparticles
SB-SNO-03-NP
Pricing > SDS > Data Sheet >
(4N) 99.99% Antimony Tin Oxide Nanoparticles
SB-SNO-04-NP
Pricing > SDS > Data Sheet >
(5N) 99.999% Antimony Tin Oxide Nanoparticles
SB-SNO-05-NP
Pricing > SDS > Data Sheet >

Antimony Tin Oxide Nanoparticles Properties (Theoretical)

Molecular Weight 444.23
Appearance Blue Powder
Melting Point N/A
Boiling Point N/A
Density 6.8 g/cm3
Bulk Density 0.95 g/cm3
True Density 6.8 g/cm3
Size Range N/A
Average Particle Size 15 nm
Specific Surface Area 47 m2/g
Morphology N/A
Crystal Phase / Structure Tetragonal

Antimony Tin Oxide Nanoparticles Health & Safety Information

Signal Word Warning
Hazard Statements H315-H319
Hazard Codes N/A
Precautionary Statements P305 + P351 + P338
Risk Codes 36/37/38
Safety Statements 26
RTECS Number N/A
Transport Information UN 1549 6.1/PG 3
WGK Germany 3
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 03/26/2019
Date Revised: 05/15/2015

SECTION 1. IDENTIFICATION

Product Name: Antimony Tin Oxide Nanoparticles

Product Number: All applicable American Elements product codes, e.g. SB-SNO-02-NP , SB-SNO-03-NP , SB-SNO-04-NP , SB-SNO-05-NP

CAS #: 128221-48-7

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008
GHS07
Acute Tox. 4 H302 Harmful if swallowed.
Acute Tox. 4 H332 Harmful if inhaled.
Hazards not otherwise classified
No data available.
Label elements
Labelling according to Regulation (EC) No 1272/2008
The substance is classified and labeled according to the CLP regulation.
Hazard pictograms

Exclamation Mark - GHS07

GHS07
Signal word: Warning
Hazard statements
H302+H332 Harmful if swallowed or if inhaled.
Precautionary statements
P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 Wash thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P304+P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P330 Rinse mouth.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.
WHMIS classification
D1B - Toxic material causing immediate and serious toxic effects
Classification system
HMIS ratings (scale 0-4)
(Hazardous Materials Identification System)
Health (acute effects) = 1
Flammability = 0
Physical Hazard = 1
Other hazards
Results of PBT and vPvB assessment:
PBT: N/A.
vPvB: N/A.


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substances
CAS No. / Substance Name:
128221-48-7
Antimony tin oxide
Identification number(s):
Index number: 051-003-00-9


SECTION 4. FIRST AID MEASURES

Description of first aid measures
If inhaled:
Supply fresh air. If not breathing, provide artificial respiration. Keep patient warm.
Seek immediate medical advice.
In case of skin contact:
Immediately wash with soap and water; rinse thoroughly.
Seek immediate medical advice.
In case of eye contact:
Rinse opened eye for several minutes under running water. Consult a physician.
If swallowed:
Seek medical treatment.
Information for doctor
Most important symptoms and effects, both acute and delayed
No information available.
Indication of any immediate medical attention and special treatment needed
No information available.


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Product is not flammable. Use fire-fighting measures that suit the surrounding fire.
Special hazards arising from the substance or mixture
If this product is involved in a fire, the following can be released:
Metal oxide fume
Antimony oxides
Advice for firefighters
Protective equipment:
Wear self-contained respirator.
Wear fully protective impervious suit.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
Environmental precautions:
Do not allow material to be released to the environment without official permits.
Methods and material for containment and cleanup:
Dispose of contaminated material as waste according to section 13.
Ensure adequate ventilation.
Prevention of secondary hazards:
No special measures required.
Reference to other sections
See Section 7 for information on safe handling
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.


SECTION 7. HANDLING AND STORAGE

Handling
Precautions for safe handling
Keep container tightly sealed.
Store in cool, dry place in tightly closed containers.
Ensure adequate ventilation.
Information about protection against explosions and fires:
The product is not flammable
Conditions for safe storage, including any incompatibilities
Storage
Requirements to be met by storerooms and receptacles:
No special requirements.
Information about storage in one common storage facility:
Store away from oxidizing agents.
Further information about storage conditions:
Keep container tightly sealed.
Store in cool, dry conditions in well-sealed containers.
Specific end use(s)
No information available.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Additional information about design of technical systems:
Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least 100 feet per minute.
Control parameters
Components with limit values that require monitoring at the workplace:
Antimony and antimony compounds
mg/m3
ACGIH TLV 0.5
Austria MAK 0.5
Belgium TWA 0.5
Denmark TWA 0.5
Finland TWA 0.5
France VME 0.5
Germany MAK 0.5 (total dust)
Hungary TWA 0.5-STEL
Japan OEL 0.1; 2B Carcinogen
Korea TLV 0.5
Ireland TWA 0.5
Netherlands MAC-TGG 0.5
Norway TWA 0.5
Poland TWA 0.5; 1.5-STEL
Russia TWA 0.2; 0.5-STEL
Sweden NGV 0.5
Switzerland MAK-W 0.5
United Nations TWA 0.5
USA PEL 0.5
Tin metal, tin oxide and inorganic tin compounds, except tin hydride, as Sn
mg/m3
ACGIH TLV 2
Austria MAK 2
Belgium TWA 2
Denmark TWA 2
Finland TWA 2
Germany MAK 2
Hungary TWA 1; 2-STEL (skin)
Netherlands MAC-TGG 2
Norway TWA 1
Poland TWA 2
Switzerland MAK-W 2; 4-KZG-W
United Kingdom TWA 2; 4-STEL
USA PEL 2
Antimony tin oxide (100.0%)
PEL (USA) Long-term value: 0.5 mg/m³ as Sb
REL (USA) Long-term value: 0.5 mg/m³ as Sb
TLV (USA) Long-term value: 0.5 mg/m³ as Sb
EL (Canada) Long-term value: 0.5 mg/m³ as Sb
Additional information: No data
Exposure controls
Personal protective equipment
Follow typical general protective and industrial hygiene measures for handling chemicals.
Keep away from foodstuffs, beverages and feed.
Remove all soiled and contaminated clothing immediately.
Wash hands before breaks and at the end of work.
Breathing equipment:
Use suitable respirator when high concentrations are present.
Protection of hands:
Impervious gloves
Inspect gloves prior to use.
Suitability of gloves should be determined both by material and quality, the latter of which may vary by manufacturer.
Eye protection: Safety glasses
Body protection: Protective work clothing.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance:
Form: Powder
Odor: No data available.
Odor threshold: No data available.
pH: N/A.
Melting point/range: 1630 °C (2966 °F)
Boiling point/range: No data available.
Sublimation temperature / start: No data available.
Flash point: N/A
Flammability (solid, gas): No data available.
Ignition temperature: No data available.
Decomposition temperature: No data available.
Auto igniting: No data available.
Danger of explosion: Product does not present an explosion hazard.
Explosion limits:
Lower: No data available.
Upper: No data available.
Vapor pressure: N/A.
Density: No data available.
Relative density: No data available.
Vapor density: N/A.
Evaporation rate: N/A.
Solubility in Water (H2O): Insoluble
Partition coefficient (n-octanol/water): No data available.
Viscosity:
Dynamic: N/A.
Kinematic: N/A.
Other information
No information available.


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available.
Chemical stability
Stable under recommended storage conditions.
Thermal decomposition / conditions to be avoided:
Decomposition will not occur if used and stored according to specifications.
Possibility of hazardous reactions
No dangerous reactions known
Conditions to avoid
No information available.
Incompatible materials:
Oxidizing agents
Hazardous decomposition products:
Metal oxide fume
Antimony oxides


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity:
Harmful if inhaled.
Harmful if swallowed.
LD/LC50 values that are relevant for classification: No data
Skin irritation or corrosion: May cause irritation
Eye irritation or corrosion: May cause irritation
Sensitization: No sensitizing effects known.
Germ cell mutagenicity: N/A
Carcinogenicity:
No classification data on carcinogenic properties of this material is available from the EPA, IARC, NTP, OSHA or ACGIH.
Reproductive toxicity: N/A
Specific target organ system toxicity - repeated exposure: N/A
Specific target organ system toxicity - single exposure: N/A
Aspiration hazard: N/A
Subacute to chronic toxicity:
Antimony compounds may cause metallic taste, gastrointestinal disturbances, vomiting, diarrhea, dizziness and systemic poisoning. Chronic exposure may cause liver and kidney damage. Dermatitis and eczematous skin eruptions may result from skin contact.
Metallic tin and inorganic tin compounds may cause nausea, vomiting, diarrhea, irritation and pneumoconiosis.
Subacute to chronic toxicity: N/A
Additional toxicological information:
To the best of our knowledge the acute and chronic toxicity of this substance is not fully known.
Carcinogenic categories
OSHA-Ca (Occupational Safety & Health Administration)
Substance is not listed.


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
Aquatic toxicity:
No information available.
Persistence and degradability:
No information available.
Bioaccumulative potential:
No information available.
Mobility in soil:
No information available.
Ecotoxical effects:
Remark:
Toxic for aquatic organisms
Additional ecological information:
General notes:
Do not allow material to be released to the environment without official permits.
Toxic for aquatic organisms
Do not allow product to reach ground water, water course or sewage system.
Danger to drinking water if even small quantities leak into the ground.
Also poisonous for fish and plankton in water bodies.
Toxic to aquatic life.
May cause long lasting harmful effects to aquatic life.
Avoid transfer into the environment.
Results of PBT and vPvB assessment:
PBT: N/A.
vPvB: N/A.
Other adverse effects
No information available.


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Recommendation:
Consult state, local or national regulations to ensure proper disposal.
Uncleaned packagings:
Recommendation:
Disposal must be made according to official regulations.


SECTION 14. TRANSPORT INFORMATION

UN-Number
DOT, IMDG, IATA
UN1549
UN proper shipping name
DOT
Antimony compounds, inorganic, solid, n.o.s. (Antimony tin oxide)
IMDG
ANTIMONY COMPOUND, INORGANIC, SOLID, N.O.S. (Antimony tin oxide),
MARINE POLLUTANT
IATA
ANTIMONY COMPOUND, INORGANIC, SO
LID, N.O.S. (Antimony tin oxide)
Transport hazard class(es)
DOT
Class
6.1 Toxic substances.
Label
6.1
Class
6.1 (T5) Toxic substances
Label
6.1
IMDG
Class
6.1 Toxic substances.
IATA
Class
6.1 Toxic substances.
Label
6.1
Packing group
DOT, IMDG, IATA
III
Environmental hazards:
Environmentally hazardous substance, solid; Marine Pollutant
Marine pollutant (IMDG):
Yes (P)
Symbol (fish and tree)
Special precautions for user
Warning: Toxic substances
EMS Number:
F-A,S-A
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N/A.
Transport/Additional information:
DOT
Marine Pollutant (DOT):
No
Remarks:
Special marking with the symbol (fish and tree).
UN "Model Regulation":
UN1549, Antimony compounds, inorganic, solid, n.o.s. (Antimony tin oxide), 6.1, III


SECTION 15. REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations
All components of this product are listed in the U.S. Environmental Protection Agency Toxic Substances Control Act Chemical substance Inventory.
All components of this product are listed on the Canadian Domestic Substances List (DSL).
SARA Section 313 (specific toxic chemical listings)
Antimony tin oxide
California Proposition 65
Prop 65 - Chemicals known to cause cancer
Substance is not listed.
Prop 65 - Developmental toxicity
Substance is not listed.
Prop 65 - Developmental toxicity, female
Substance is not listed.
Prop 65 - Developmental toxicity, male
Substance is not listed.
Information about limitation of use:
For use only by technically qualified individuals.
This product contains antimony and is subject to the reporting requirements of section 313 of the Emergency Planning and Community Right to know Act of 1986 and 40CFR372.
Other regulations, limitations and prohibitive regulations
Substance of Very High Concern (SVHC) according to the REACH Regulations (EC) No. 1907/2006.
Substance is not listed.
The conditions of restrictions according to Article 67 and Annex XVII of the Regulation (EC) No 1907/2006 (REACH) for the manufacturing, placing on the market and use must be observed.
Substance is not listed.
Annex XIV of the REACH Regulations (requiring Authorisation for use)
Substance is not listed.
Chemical safety assessment:
A Chemical Safety Assessment has not been carried out.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2018 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Antimony Tin Oxide Nanoparticles

Oxide IonHigh Purity, D50 = +10 nanometer (nm) by SEMAntimony Tin Oxide (ATO) Nanoparticles, nanopowder, nanodots or nanocrystals are spherical or faceted high surface area nanocrystalline alloy particles with magnetic properties. Nanoscale Antimony Tin Oxide (ATO) Particles are typically 20-40 nanometers (nm) with specific surface area (SSA) in the 30 - 50 m2/g range and also available in with an average particle size of 100 nm range with a specific surface area of approximately 7 m2/g. Nano Antimony Tin Oxide (ATO) Particles are also available in ultra high purity and high purity and coated and dispersed forms. They are also available as a nanofluid through the AE Nanofluid production group. Nanofluids are generally defined as suspended nanoparticles in solution either using surfactant or surface charge technology. Nanofluid dispersion and coating selection technical guidance is also available. Other nanostructures include nanorods, nanowhiskers, nanohorns, nanopyramids and other nanocomposites. Surface functionalized nanoparticles allow for the particles to be preferentially adsorbed at the surface interface using chemically bound polymers.

Antimony Tin Oxide Nanoparticles Synonyms

ATO, antimony doped tin oxide, antimony-doped tin oxide, Sb-Sn-O, 68187-54-2, antimony stannate, tin antimonate, tin(IV) antimonate, dioxotin oxo(oxostibanyloxy)stibane, 549541

Chemical Identifiers

Linear Formula Sb2SnO5
MDL Number MFCD00799153
EC No. N/A
Beilstein Registry No. N/A
Pubchem CID 56845640
IUPAC Name dioxotin; oxo(oxostibanyloxy)stibane
SMILES O=[Sn]=O.O=[Sb]O[Sb]=O
InchI Identifier InChI=1S/5O.2Sb.Sn
InchI Key DCEPJBOKQZTMOG-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

See more Antimony products. Antimony (atomic symbol: Sb, atomic number: 51) is a Block P, Group 15, Period 5 element with an atomic radius of 121.760. Antimony Bohr Model The number of electrons in each of antimony's shells is 2, 8, 18, 18, 5 and its electron configuration is [Kr] 4d10 5s2 5p3. The antimony atom has a radius of 140 pm and a Van der Waals radius of 206 pm. Antimony was discovered around 3000 BC and first isolated by Vannoccio Biringuccio in 1540 AD. In its elemental form, antimony has a silvery lustrous gray appearance. Elemental Antimony The most common source of antimony is the sulfide mineral known as stibnite (Sb2S3), although it sometimes occurs natively as well. Antimony has numerous applications, most commonly in flame-retardant materials it also increases the hardness and strength of lead when combined in an alloy and is frequently employed as a dopant in semiconductor materials. Its name is derived from the Greek words anti and monos, meaning a metal not found by itself.

Tin Bohr ModelSee more Tin products. Tin (atomic symbol: Sn, atomic number: 50) is a Block P, Group 14, Period 5 element with an atomic weight of 118.710. The number of electrons in each of tin's shells is 2, 8, 18, 18, 4 and its electron configuration is [Kr] 4d10 5s2 5p2. The tin atom has a radius of 140.5 pm and a Van der Waals radius of 217 pm.In its elemental form, tin has a silvery-gray metallic appearance. It is malleable, ductile and highly crystalline. High Purity (99.9999%) Tin (Sn) MetalTin has nine stable isotopes and 18 unstable isotopes. Under 3.72 degrees Kelvin, Tin becomes a superconductor. Applications for tin include soldering, plating, and such alloys as pewter. The first uses of tin can be dated to the Bronze Age around 3000 BC in which tin and copper were combined to make the alloy bronze. The origin of the word tin comes from the Latin word Stannum which translates to the Anglo-Saxon word tin. For more information on tin, including properties, safety data, research, and American Elements' catalog of tin products, visit the Tin element page.

TODAY'S SCIENCE POST!

March 26, 2019
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day

Rapid magnetic 3D printing of human cells