CAS #:

Linear Formula:

SnSe2

MDL Number:

N/A

EC No.:

N/A

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Tin(IV) Selenide Sputtering Target
SN4-SE-02-ST
Pricing > SDS > Data Sheet >
(3N) 99.9% Tin(IV) Selenide Sputtering Target
SN-SE-03-ST
Pricing > SDS > Data Sheet >
(4N) 99.99% Tin(IV) Selenide Sputtering Target
SN4-SE-04-ST
Pricing > SDS > Data Sheet >
(5N) 99.999% Tin(IV) Selenide Sputtering Target
SN4-SE-05-ST
Pricing > SDS > Data Sheet >

Tin(IV) Selenide Sputtering Target Properties (Theoretical)

Compound Formula Se2Sn
Molecular Weight 276.63
Appearance Red-brown solid
Melting Point 650 °C
Boiling Point N/A
Density 5.13 g/cm3
Solubility in H2O N/A
Exact Mass 279.735237
Monoisotopic Mass 279.735237

Tin(IV) Selenide Sputtering Target Health & Safety Information

Signal Word N/A
Hazard Statements N/A
Hazard Codes N/A
Risk Codes N/A
Safety Statements N/A
Transport Information N/A
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 06/05/2020
Date Revised: 05/15/2015

SECTION 1. IDENTIFICATION

Product Name: Tin(IV) Selenide Sputtering Target

Product Number: All applicable American Elements product codes, e.g. SN4-SE-02-ST , SN-SE-03-ST , SN4-SE-04-ST , SN4-SE-05-ST

CAS #: 20770-09-6

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

H
MIS
Health Ratings (0-4):
Health: 2
Flammability: 1
Physical: 1

Skull and Crossbones - GHS06 Health Hazard - GHS08

Signal Word: Danger
Hazard Statements:
H301+H331: Toxic if swallowed or if inhaled
H373: May cause damage to organs through prolonged or repeated exposure
Precautionary Statements:
P260: Do not breathe dust/fume/gas/mist/vapors/spray
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
P405: Store locked up
P501: Dispose of contents/container in accordance with local/regional/national/international regulations


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Family: Ceramic
Additional Names: Tin(IV) Selenide
Tin selenide (SnSe2):
Percentage: 100 wt%
CAS#: 20770-09-6


SECTION 4. FIRST AID MEASURES

General Treatment:
Seek medical attention if symptoms persist.
Special Treatment:
Immediately remove any clothing soiled by the product. Remove breathing apparatus only after contaminated clothing has been completely removed. In case of irregular breathing or respiratory arrest provide artificial respiration
Important Symptoms:
None
Inhalation:
Remove victim to fresh air. Supply oxygen if breathing is difficult.
Ingestion:
Seek medical attention.
Skin:
Wash affected area with mild soap and water. Remove any contaminated clothing.
Eyes:
Flush eyes with water, blinking often for several minutes. Remove contact lenses if present and easy to do. Continue rinsing


SECTION 5. FIREFIGHTING MEASURES

Flammability:
Flammable as powder
Extinguishing Media:
Do not use water for metal fires –use CO2, sand, extinguishing powder.
Spec. Fire Fighting Procedure:
Use full-face, self-contained breathing apparatus with full protective clothing to prevent contact with skin and eyes.
See section 10 for decomposition products.


SECTION 6. ACCIDENTAL RELEASE MEASURES

If Material Is Released/Spilled:
Wear appropriate respiratory and protective equipment specified in special protection information. Isolate spill area and provide ventilation. Vacuum up spill using a high efficiency particulate
absolute (HEPA) air filter and place in a closed container for disposal.
Take care not to raise dust.
Environmental Precautions:
Isolate runoff to prevent environmental pollution.


SECTION 7. HANDLING AND STORAGE

Handling Conditions:
Wash thoroughly after handling.
Storage Conditions:
Store in a cool dry place in a tightly sealed container. Store apart from materials and conditions listed in section 10.
Work/Hygienic Maintenance:
Do not use tobacco or food in work area. Wash thoroughly before eating and smoking. Do not blow dust off clothing or skin with compressed air.
Ventilation:
Provide sufficient ventilation to maintain concentration at or below threshold limit.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Permissible Exposure Limits:
0.2 mg/m3 as Se, long-term value
Threshold Limit Value:
0.2 mg/m3 as Se, long-term value
Special Equipment:
None
Respiratory Protection:
Dust Respirator
Protective Gloves:
Rubber gloves
Eye Protection:
Safety glasses or goggles
Body Protection:
Protective work clothing. Wear close-toed shoes and long sleeves/pants.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Color: N/A
Form: Powder/Pieces
Odor: N/A
Water Solubility: Insoluble
Boiling Point: N/A
Melting Point: N/A
Flash Point: N/A
Autoignition Temperature: N/A
Density: N/A
Molecular weight: 276.63 g/mol


SECTION 10. STABILITY AND REACTIVITY

Stability:
Stable under recommended storage conditions
Reacts With:
Oxidizing agents
Incompatible Conditions:
None
Hazardous Decomposition Products:
Metal oxide fume


SECTION 11. TOXICOLOGICAL INFORMATION

Potential Health Effects:
Eyes:
Causes irritating effect
Skin:
Irritating to skin and mucous membranes
Ingestion:
May cause irritation
Inhalation:
May cause irritation
Chronic:
Selenium may cause amyotropic lateral sclerosis, bronchial irritation, gastrointestinal distress, vasopharyngeal irritation, garlic odor on breath and sweat, metallic taste, pallor, irritability, excessive fatigue, loss of fingernails and hair, pulmonary edema, anemia and weight loss.
Metallic tin and inorganic tin compounds may cause nausea, vomiting, diarrhea, irritation, and pneumoconiosis.
Signs & Symptoms:
N/A
Aggravated Medical Conditions:
N/A
Median Lethal Dose:
N/A
Carcinogen:
NTP-R: Reasonably anticipated to be a carcinogen, limited evidence of carcinogenicity from epidemiologic studies.
IARC-3: Not classifiable as to carcinogenicity to humans.
EPA-D: Not classifiable as to human carcinogenicity: inadequate human and animal evidence of carcinogenicity or no data are available.


SECTION 12. ECOLOGICAL INFORMATION

Aquatic Toxicity:
High
Persistent Bioaccumulation Toxicity:
No
Very Persistent, Very Bioaccumulative:
No
Notes:
Very toxic for aquatic organism.
May cause long lasting harmful effect on aquatic life.
Do not allow material to be released to the environment without official permits.
Do not allow product to reach any water sources.
Danger to drinking water if even extremely small quantities leak into the ground.
Also poisonous for fish and plankton in water bodies
Avoid transfer into the environment.


SECTION 13. DISPOSAL CONSIDERATIONS

Dispose of in accordance with local, state, national, and international regulations.


SECTION 14. TRANSPORT INFORMATION

Hazardous: Hazardous for transportation.
Hazard Class: 6.1 Toxic substances.
Packing Group: III
UN Number: UN 3283
Proper Shipping Name: Selenium compound, solid, n.o.s.(Tin selenide)


SECTION 15. REGULATORY INFORMATION

National regulations
All components of this product are listed in the U.S. Environmental Protection Agency Toxic Substances Control Act Chemical substance Inventory.
All components of this product are listed on the Canadian Non-Domestic Substances List (NDSL).
SARA Section 313 (specific toxic chemical listings)
20770-09-6 Tin selenide
California Proposition 65
Prop 65 - Chemicals known to cause cancer
Substance is not listed.
Prop 65 - Developmental toxicity
Substance is not listed.
Prop 65 - Developmental toxicity, female
Substance is not listed.
Prop 65 - Developmental toxicity, male
Substance is not listed.
Information about limitation of use:
For use only by technically qualified individuals.
This product contains selenium and is subject to the reporting requirements of section 313 of the Emergency Planning and Community Right to Know Act of 1986 and 40CFR372.
Other regulations, limitations and prohibitive regulations
Substance of Very High Concern (SVHC) according to the REACH Regulations (EC) No. 1907/2006.
Substance is not listed.
The conditions of restrictions according to Article 67 and Annex XVII of the Regulation (EC) No 1907/2006 (REACH) for the manufacturing, placing on the market and use must be observed.
Substance is not listed.
Annex XIV of the REACH Regulations (requiring Authorisation for use)
Substance is not listed.
Chemical safety assessment:
A Chemical Safety Assessment has not been carried out.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2018 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Tin(IV) Selenide Sputtering Target

American Elements specializes in producing high purity Tin(IV) Selenide Sputtering Targets with the highest possible density High Purity (99.99%) Tin(IV) Selenide Sputtering Targetand smallest possible average grain sizes for use in semiconductor, chemical vapor deposition (CVD) and physical vapor deposition (PVD) display and optical applications. Our standard sputtering targets for thin film deposition are available monoblock or bonded with planar target dimensions and configurations up to 820 mm with hole drill locations and threading, beveling, grooves and backing designed to work with both older sputtering devices as well as the latest process equipment, such as large area coating for solar energy or fuel cells and flip-chip applications. Rotary (cylindrical), round, rectangular, square, ring, annular, oval, "dog-bone" and other shaped targets are available in standard, custom, and research sized dimensions. All targets are analyzed using best demonstrated techniques including X-Ray Fluorescence (XRF), Glow Discharge Mass Spectrometry (GDMS), and Inductively Coupled Plasma (ICP). Materials are produced using crystallization, solid state and other ultra high purification processes such as sublimation. American Elements specializes in producing custom compositions for commercial and research applications and for new proprietary technologies. Please request a quote above for more information on lead time and pricing.

Tin(IV) Selenide Sputtering Target Synonyms

Tin selenide; Tin diselenide; Stannic selenide; Diselenoxostannane; Tin(4+) diselenide

Chemical Identifiers

Linear Formula SnSe2
MDL Number N/A
EC No. N/A
Beilstein/Reaxys No. N/A
Pubchem CID 14513327
IUPAC Name bis(selanylidene)tin
SMILES [Se]=[Sn]=[Se]
InchI Identifier InChI=1S/2Se.Sn
InchI Key KBPGBEFNGHFRQN-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Payment Methods

American Elements accepts checks, wire transfers, ACH, most major credit and debit cards (Visa, MasterCard, AMEX, Discover) and Paypal.

For the convenience of our international customers, American Elements offers the following additional payment methods:

SOFORT bank tranfer payment for Austria, Belgium, Germany and SwitzerlandJCB cards for Japan and WorldwideBoleto Bancario for BraziliDeal payments for the Netherlands, Germany, Austria, Belgium, Italy, Poland, Spain, Switzerland, and the United KingdomGiroPay for GermanyDankort cards for DenmarkElo cards for BrazileNETS for SingaporeCartaSi for ItalyCarte-Bleue cards for FranceChina UnionPayHipercard cards for BrazilTROY cards for TurkeyBC cards for South KoreaRuPay for India

Related Elements

Selenium Bohr ModelSee more Selenium products. Selenium (atomic symbol: Se, atomic number: 34) is a Block P, Group 16, Period 4 element with an atomic radius of 78.96. The number of electrons in each of Selenium's shells is 2, 8, 18, 6 and its electron configuration is [Ar] 3d10 4s2 4p4. The selenium atom has a radius of 120 pm and a Van der Waals radius of 190 pm. Selenium is a non-metal with several allotropes: a black, vitreous form with an irregular crystal structure three red-colored forms with monoclinic crystal structures and a gray form with a hexagonal crystal structure, the most stable and dense form of the element. Elemental SeleniumOne of the most common uses for selenium is in glass production the red tint that it lends to glass neutralizes green or yellow tints from impurities in the glass materials. Selenium was discovered and first isolated by Jöns Jakob Berzelius and Johann Gottlieb Gahn in 1817. The origin of the name Selenium comes from the Greek word "Selênê," meaning moon.

Tin Bohr ModelSee more Tin products. Tin (atomic symbol: Sn, atomic number: 50) is a Block P, Group 14, Period 5 element with an atomic weight of 118.710. The number of electrons in each of tin's shells is 2, 8, 18, 18, 4 and its electron configuration is [Kr] 4d10 5s2 5p2. The tin atom has a radius of 140.5 pm and a Van der Waals radius of 217 pm.In its elemental form, tin has a silvery-gray metallic appearance. It is malleable, ductile and highly crystalline. High Purity (99.9999%) Tin (Sn) MetalTin has nine stable isotopes and 18 unstable isotopes. Under 3.72 degrees Kelvin, Tin becomes a superconductor. Applications for tin include soldering, plating, and such alloys as pewter. The first uses of tin can be dated to the Bronze Age around 3000 BC in which tin and copper were combined to make the alloy bronze. The origin of the word tin comes from the Latin word Stannum which translates to the Anglo-Saxon word tin. For more information on tin, including properties, safety data, research, and American Elements' catalog of tin products, visit the Tin element page.

TODAY'S SCIENCE POST!

June 05, 2020
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day

A new 3D imaging technique called harmonic optical tomography